[Q34-Q54] Updated Dec-2025 Exam Engine or PDF for the NSE7_OTS-7.2 Tests Free Updated Today!

4/5 - (1 vote)

Updated Dec-2025 Exam Engine or PDF for the NSE7_OTS-7.2 Tests Free Updated Today!

Ultimate Guide to Prepare NSE7_OTS-7.2 with Accurate PDF Questions

Q34. Refer to the exhibit.

Which statement about the interfaces shown in the exhibit is true?

port2, port2-vlan10, and port2-vlan1 are part of the software switch interface.

The VLAN ID of port1-vlan1 can be changed to the VLAN ID 10.

port1-vlan10 and port2-vlan10 are part of the same broadcast domain

port1, port1-vlan10, and port1-vlan1 are in different broadcast domains

Q35. Refer to the exhibit.

You need to configure VPN user access for supervisors at the breach and HQ sites using the same soft FortiToken. Each site has a FortiGate VPN gateway.
What must you do to achieve this objective?

You must use a FortiAuthenticator.

You must register the same FortiToken on more than one FortiGate.

You must use the user self-registration server.

You must use a third-party RADIUS OTP server.

Q36. An OT network consists of multiple FortiGate devices. The edge FortiGate device is deployed as the secure gateway and is only allowing remote operators to access the ICS networks on site.
Management hires a third-party company to conduct health and safety on site. The third-party company must have outbound access to external resources.
As the OT network administrator, what is the best scenario to provide external access to the third-party company while continuing to secure the ICS networks?

Configure outbound security policies with limited active authentication users of the third-party company.

Create VPN tunnels between downstream FortiGate devices and the edge FortiGate to protect ICS network traffic.

Split the edge FortiGate device into multiple logical devices to allocate an independent VDOM for the third-party company.

Implement an additional firewall using an additional upstream link to the internet.

Q37. When you create a user or host profile, which three criteria can you use? (Choose three.)

Host or user group memberships

Administrative group membership

An existing access control policy

Location

Host or user attributes

Q38. Refer to the exhibit.

You are creating a new operational technology (OT) rule to monitor Modbus protocol traffic on FortiSIEM Which action must you take to ensure that all Modbus messages on the network match the rule?

Add a new condition to filter Modbus traffic based on the source TCP/UDP port

The condition on the SubPattern filter must use the AND logical operator

the Aggregate section, set the attribute value to equal to or greater than 0

In the Group By section remove all attributes that are not configured in the Filter section

Q39. Refer to the exhibit.

Based on the Purdue model, which three measures can be implemented in the control area zone using the Fortinet Security Fabric? (Choose three.)

FortiGate for SD-WAN

FortiGate for application control and IPS

FortiNAC for network access control

FortiSIEM for security incident and event management

FortiEDR for endpoint detection

Q40. Refer to the exhibit.

The IPS profile is added on all of the security policies on FortiGate.
For an OT network, which statement of the IPS profile is true?

FortiGate has no IPS industrial signature database enabled.

The listed IPS signatures are classified as SCADAapphcat nns

All IPS signatures are overridden and must block traffic match signature patterns.

The IPS profile inspects only traffic originating from SCADA equipment.

Q41. Refer to the exhibit.

You are creating a new operational technology (OT) rule to monitor Modbus protocol traffic on FortiSIEM Which action must you take to ensure that all Modbus messages on the network match the rule?

Add a new condition to filter Modbus traffic based on the source TCP/UDP port

The condition on the SubPattern filter must use the AND logical operator

the Aggregate section, set the attribute value to equal to or greater than 0

In the Group By section remove all attributes that are not configured in the Filter section

Q42. An administrator wants to use FortiSoC and SOAR features on a FortiAnalyzer device to detect and block any unauthorized access to FortiGate devices in an OT network.
Which two statements about FortiSoC and SOAR features on FortiAnalyzer are true? (Choose two.)

You must set correct operator in event handler to trigger an event.

You can automate SOC tasks through playbooks.

Each playbook can include multiple triggers.

You cannot use Windows and Linux hosts security events with FortiSoC.

Q43. Refer to the exhibit.

Based on the topology designed by the OT architect, which two statements about implementing OT security are true? (Choose two.)

Firewall policies should be configured on FortiGate-3 and FortiGate-4 with industrial protocol sensors.

Micro-segmentation can be achieved only by replacing FortiGate-3 and FortiGate-4 with a pair of FortiSwitch devices.

IT and OT networks are separated by segmentation.

FortiGate-3 and FortiGate-4 devices must be in a transparent mode.

Q44. An OT network architect needs to secure control area zones with a single network access policy to provision devices to any number of different networks. On which device can this be accomplished?

FortiGate

FortiEDR

FortiSwitch

FortiNAC

Q45. An OT network consists of multiple FortiGate devices. The edge FortiGate device is deployed as the secure gateway and is only allowing remote operators to access the ICS networks on site.
Management hires a third-party company to conduct health and safety on site. The third-party company must have outbound access to external resources. As the OT network administrator, what is the best scenario to provide external access to the third- party company while continuing to secure the ICS networks?

Create VPN tunnels between downstream FortiGate devices and the edge FortiGate to protect ICS network traffic.

Split the edge FortiGate device into multiple logical devices to allocate an independent VDOM for the third-party company.

Implement an additional firewall using an additional upstream link to the internet.

Configure outbound security policies with limited active authentication users of the third-party company.

Q46. As an OT administrator, it is important to understand how industrial protocols work in an OT network.
Which communication method is used by the Modbus protocol?

It uses OSI Layer 2 and the primary device sends data based on request from secondary device.

It uses OSI Layer 2 and both the primary/secondary devices always send data during the communication.

It uses OSI Layer 2 and both the primary/secondary devices send data based on a matching token ring.

It uses OSI Layer 2 and the secondary device sends data based on request from primary device.

Q47. Refer to the exhibit.

An OT network security audit concluded that the application sensor requires changes to ensure the correct security action is committed against the overrides filters.
Which change must the OT network administrator make?

Set all application categories to apply default actions.

Change the security action of the industrial category to monitor.

Set the priority of the C.BO.NA.1 signature override to 1.

Remove IEC.60870.5.104 Information.Transfer from the first filter override.

According to the Fortinet NSE 7 – OT Security 6.4 exam guide1, the application sensor settings allow you to configure the security action for each application category andnetwork protocol override. The security action determines how the FortiGate unit handles traffic that matches the application category or network protocol override. The security action can be one of the following:
* Allow: The FortiGate unit allows the traffic without any further inspection.
* Monitor: The FortiGate unit allows the traffic and logs it for monitoring purposes.
* Block: The FortiGate unit blocks the traffic and logs it as an attack.
The priority of the network protocol override determines the order in which the FortiGate unit applies the security action to the traffic. The lower the priority number, the higher the priority. For example, a priority of 1 is higher than a priority of 10.
In the exhibit, the application sensor has the following settings:
* The industrial category has a security action of allow, which means that the FortiGate unit will not inspect or log any traffic that belongs to this category.
* The IEC.60870.5.104 Information.Transfer network protocol override has a security action of block, which means that the FortiGate unit will block and log any traffic that matches this protocol.
* The IEC.60870.5.104 Control.Functions network protocol override has a security action of monitor, which means that the FortiGate unit will allow and log any traffic that matches this protocol.
* The IEC.60870.5.104 Start/Stop network protocol override has a security action of allow, which means that the FortiGate unit will not inspect or log any traffic that matches this protocol.
* The IEC.60870.5.104 Transfer.C.BO.NA.1 network protocol override has a security action of block, which means that the FortiGate unit will block and log any traffic that matches this protocol.
The problem with these settings is that the IEC.60870.5.104 Transfer.C.BO.NA.1 network protocol override has a lower priority than the IEC.60870.5.104 Information.Transfer network protocol override. This means that if the traffic matches both protocols, the FortiGate unit will apply the security action of the higher priority override, which is block. However, the IEC.60870.5.104 Transfer.C.BO.NA.1 protocol is used to transfer binary outputs, which are essential for controlling OT devices. Therefore, blocking this protocol could have negative consequences for the OT network.
To fix this issue, the OT network administrator must set the priority of the IEC.60870.5.104 Transfer.C.BO.NA.1 network protocol override to 1, which is higher than the priority of the IEC.60870.5.104 Information.Transfer network protocol override. This way, the FortiGate unit will apply the security action of the lower priority override, which is allow, to the traffic that matches both protocols. This will ensure that the FortiGate unit does not block the traffic that is used to transfer binary outputs, while still blocking the traffic that is used to transfer information.
1: NSE 7 Network Security Architect – Fortinet

Q48. An administrator wants to use FortiSoC and SOAR features on a FortiAnalyzer device to detect and block any unauthorized access to FortiGate devices in an OT network. Which two statements about FortiSoC and SOAR features on FortiAnalyzer are true? (Choose two.)

You must set correct operator in event handler to trigger an event.

You can automate SOC tasks through playbooks.

Each playbook can include multiple triggers.

You cannot use Windows and Linux hosts security events with FortiSoC.

Q49. Refer to the exhibits.

Which statement is true about the traffic passing through to PLC-2?

IPS must be enabled to inspect application signatures.

The application filter overrides the default action of some IEC 104 signatures.

IEC 104 signatures are all allowed except the C.BO.NA 1 signature.

SSL Inspection must be set to deep-inspection to correctly apply application control.

Q50. Refer to the exhibit.
Which statement is true about application control inspection?

The industrial application control inspection process is unique among application categories.

Security actions cannot be applied on the lowest level of the hierarchy.

You can control security actions only on the parent-level application signature

The parent signature takes precedence over the child application signature.

Q51. Refer to the exhibit.

Given the configurations on the FortiGate, which statement is true?

FortiGate is configured with forward-domains to reduce unnecessary traffic.

FortiGate is configured with forward-domains to forward only domain controller traffic.

FortiGate is configured with forward-domains to forward only company domain website traffic.

FortiGate is configured with forward-domains to filter and drop non-domain controller traffic.

Q52. An OT customer is using multiple FortiGate devices in their network to implement two-factor authentication with hardware FortiTokens. A supervisor is carrying multiple FortiTokens to be used when logging in to a critical server behind different FortiGate devices.
As an OT network architect, which approach must you take in order to assign one token per user and still use two-factor authentication on multiple FortiGate devices?

Implement a FortiManager and manage all FortiGate devices in the OT network to share the FortiTokens database.

Implement FortiAuthenticator with FortiTokens provisioned for each user, and configure FortiAuthenticator as remote authentication server on all FortiGate devices in the OT network.

Provision the Edge-FortiGate device with all the FortiTokens and configure it as a remote authentication server on other FortiGate devices.

Configure FSSO-based two-factor authentication.

Q53. Which three Fortinet products can you use for device identification in an OT industrial control system (ICS)?
(Choose three.)

FortiSIEM

FortiManager

FortiAnalyzer

FortiGate

FortiNAC

Q54. Refer to the exhibit.

An OT architect has implemented a Modbus TCP with a simulation server Conpot to identify and control the Modus traffic in the OT network. The FortiGate-Edge device is configured with a software switch interface ssw-01.
Based on the topology shown in the exhibit, which two statements about the successful simulation of traffic between client and server are true? (Choose two.)