Prepare Civil-Engineering-Technology Question Answers Free Update With 100% Exam Passing Guarantee [Q67-Q84]

4/5 - (1 vote)

Prepare Civil-Engineering-Technology Question Answers Free Update With 100% Exam Passing Guarantee [2026]

Dumps Real CTTAM Civil-Engineering-Technology Exam Questions [Updated 2026]

CTTAM Civil-Engineering-Technology Exam Syllabus Topics:

Section	Weight	Objectives
Municipal Engineering	20%	– Water supply and distribution 1. Water quality and treatment basics 2. Water system design and hydraulics – Wastewater and stormwater management 1. Drainage and flood control 2. Sanitary and storm sewer design
Materials Testing	20%	– Soil mechanics and testing 1. Compaction and bearing capacity tests 2. Soil classification and properties – Concrete and asphalt testing 1. Field and laboratory testing procedures 2. Mix design and quality control
Structural Design Fundamentals	20%	– Design of structural elements 1. Steel and timber design basics 2. Reinforced concrete design – Structural analysis 1. Analysis of beams, columns, and frames 2. Load determination and load paths
Transportation Engineering	20%	– Highway and road design 1. Pavement design and materials 2. Geometric design principles – Traffic engineering 1. Traffic flow and capacity analysis 2. Signal design and traffic control
Surveying	20%	– Measurement and calculation techniques 1. Computation and adjustment of survey data 2. Field measurement procedures – Surveying equipment and methods 1. GPS and modern surveying technologies 2. Total station and leveling instrument operation

Q67. What substance is used to calibrate a concrete air pressure meter?

Oil

Water

Air

Concrete

Q68. Considering Occupational Health and Safety standards for trench side slopes in lieu of shoring, and a 1.2 m wide trench, what is the minimum offset from centre line to the top edge of the trench for an excavation that is
3 m deep?

1.20 m

2.40 m

3.00 m

5.20 m

Q69. What is the most important information a civil engineering technologist should be familiar with before stepping onsite during site inspection?

Owner’s name

Project completion date

Site safety rules and procedures

Number of site personnel and equipment

Q70. What documents must a contractor submit as part of a project to consultants for review?

Shop drawings

Change orders

Issued for construction drawings

Minutes of project pre-construction meeting

Q71. A civil engineering technologist is undertaking a final acceptance review of a subdivision. The technologist finds 35 m of deficient sidewalk and three hydrants which were not tested. As part of final acceptance, what should be done to ensure the hydrants get tested and the sidewalk is repaired?

Write down that three hydrants were not tested, and that 35 m of sidewalk was deficient.

Verbally communicate the locations of the hydrants and the sidewalk to the contractor.

Write down the locations of the hydrants and the sidewalk and forward the deficiency list to the contractor.

Request that the contractor write down the numbers and locations of the hydrants and the sidewalk.

Q72. The critical path refers to which of the following series of tasks in a schedule?

eect

Those that dictate the start date of a project

Those that dictate the final cost of a project

Those that dictate the final cut and fills in a project

Q73. Prior to entering an active construction site, what must all visitors do?

Put on the appropriate Personal Protective Equipment (PPE).

Check in at the site office for permission.

Show identification credentials.

Call supervisor notifying of site visit.

Q74. A continuous beam is supported in the middle and at both ends. It has a uniform load applied to the top. What will be the reactive forces at the supports?

They will be equal at all supports.

They will be greater in the middle than at the ends.

They will be greater at the ends than in the middle.

They will vary depending on whether the supports are fixed or not.

Q75. A subcontractor is completing surface rehabilitation in a mature community. What are the minimum requirements for quality that must be met?

Warranty agreement specifications

Subcontractor’s paving specifications

Developer insurance requirements

Municipality specifications

Q76. A civil engineering technologist works for a contractor. An engineer notifies him that the depth of concrete pilings needs to be increased. What is the first thing the civil engineering technologist should do?

Proceed with the work according to the original contract.

Proceed with the revised work as instructed.

Present revised environmental considerations to the project engineer.

Present the change in costs and schedules to the project manager.

Q77. Why would an owner require COR certification from a contractor?

To ensure that a contractor has first aid personnel on staff

To ensure that a contractor has a good workplace safety record

To ensure that a contractor is generally in compliance with workers’ compensation regulations

To ensure that a contractor has a quality safety management program in place

Q78. A cologist is required to inspect the installation of a sanitary service pipe to confirm the slope. The technologist measures an elevation of 705.667 at the end of the service and 705.202 at the main. The horizontal measurement from the main to the end of the service is 22.10 m. What is the slope of the pipe?

1.5%

2.0%

2.1%

2.5%

Q79. For granular material, what is the typical optimum moisture content for dry densities ranging from 2100 kg/m³ to 2200 kg/m³?

4-7%

8-15%

16-20%

21-25%

Q80. A concrete mix is onsite and at its specified slump of 80 mm. The pour requires a slump of 200 mm. The concrete onsite meets all other requirements. What action should be taken?

Order a different concrete mix

Add water to the concrete onsite

Add low-range water reducer to the concrete onsite

Add high-range water reducer to the concrete onsite

Q81. Which of the following tests are required as part of soil grain size analysis?

Sieve analysis for coarse grains and Atterberg limit tests for fine grains

Sieve analysis for coarse grains and hydrometer test for fine grains

Sieve analysis for fine grains and hydrometer test for coarse grains

Sieve analysis for fine grains and Atterberg limit tests for coarse grains

Q82. A civil engineering technologist is to inspect control joint saw-cuts on a newly poured concrete slab. What saw cut depth would be typically specified?

1/4 of the total depth of the slab

1/2 of the total depth of the slab

2/3 of the total depth of the slab

Total depth of the slab

Q83. Which of the following correctly indicates the information that must be provided on a site plan?

The legal description

Finish grades and setback distances

Finish grades and the legal description

Finish grades, setback distances, and the legal description

Q84. What two municipal plans are required to define a new civil infrastructure project?

Residential/commercial development plan and transportation plan

Municipal Development Plan and Transportation Master Plan

Residential/commercial development plan and city transit plan

Municipal Development Plan and city transit plan

Civil-Engineering-Technology Exam Dumps, Civil-Engineering-Technology Practice Test Questions: https://www.dumpleader.com/Civil-Engineering-Technology_exam.html

CTTAM Civil-Engineering-Technology Exam Syllabus Topics:

Leave a Reply Cancel reply